Procedure of Dental Implant

A typical implant consists of a titanium screw (resembling a tooth root) with a roughened surface. This surface is treated either by plasma spraying, etching or sandblasting to increase the integration potential of the implant. An osteotomy or precision hole is carefully drilled into jawbone and the implant is installed in the osteotomy.
Implant surgery is typically performed as an outpatient under general anesthesia or with Local anesthesia by trained and certified clinicians including general dentists, oral surgeons, and periodontists. An increasing number of general or cosmetic dentists as well as prosthodontists are also placing implants in relatively simple cases. The most common treatment plan calls for several surgeries over a period of months, especially if bone augmentation (bone grafting) is needed to support implant placements. At the other end of the surgery scale, some patients can be implanted and restored in a single surgery, in a procedure labeled "immediate function" and "teeth in an hour."
A single implant procedure that involves an incision and "flapping" of the gum or gingiva (to expose the jawbone) takes about an hour, sometimes longer; multiple implants can be installed in a single surgical session lasting several hours. At the conclusion, the patient goes through a period of recovery, returns to consciousness and is sent home with a relative or friend.
Healing and integration of the implant(s) with jawbone occurs over several months in a process called osseointegration. At the appropriate time, the restorative or cosmetic dentist or prosthodontist uses the implant(s) to anchor crowns or a prosthetic restoration containing several "teeth". Since the implants supporting the restoration are integrated, which means they are biomechanically stable and strong, the patient is immediately able to masticate (chew) normally.
In an immediate function procedure, the gingiva is not flapped (Flapless). Instead, the surgeon removes a small plug of gingiva directly over the drilling site. The site is drilled and the implant is installed. Then a crown is immediately added. Patients are cautioned to give their new "teeth in an hour" ample healing/integration time (weeks or months) before attempting normal mastication.
There are different approaches to place dental implants after tooth extraction. The approaches are:
Immediate post-extraction implant placement.
Delayed immediate post-extraction implant placement (2 weeks to 3 months after extraction).
Late implantation (3 months after tooth extraction).
According to the timing of loading of dental implants, the procedure of loading could be classified into:
Immediate loading procedure.
Early loading (1 week to 12 weeks).
Staged loading (3-6 months).
Late loading (more than 6 months).
Most patients need the longer treatment plan, which has an excellent history going back many years. Before surgery, with the patient fully awake or during an earlier office visit, a prudent clinician planning mandibular implants will conduct a neurosensory examination to rule out altered sensation, thus setting a base line on nerve function. Also prior to surgery, a panoramic X-ray will be taken using a metal ball of known dimension so that calibrated measurements can be made from the image (to accurately locate "vital structures" such as nerves and the position of critical anatomical features such as the mental foramen, which is the transit point in the jawbone for the nerve which innervates the lip and chin).
At edentulous (without teeth) jaw sites, a pilot hole is bored into the recipient bone, taking care to avoid vital structures (in particular the inferior alveolar nerve or IAN within the mandible). A zone of safety, usually 2 mm, is the standard of care for avoiding vital structures like the IAN. When computed tomography (3D X-ray imaging) is used preoperatively to accurately pinpoint vital structures, the zone of safety may be reduced to 1 mm through the use of computer-aided design of surgical guides.
Drilling into jawbone usually occurs in several separate steps. The pilot hole is expanded by using progressively wider drills (typically between three and seven successive drilling steps, depending on implant width and length). Care is taken not to damage the osteoblast or bone cells by overheating. A cooling saline spray keeps the temperature of the bone to below 47 degrees Celsius (approximately 117 degrees Fahrenheit). The implant screw can be self-tapping, and is screwed into place at a precise torque so as not to overload the surrounding bone (overloaded bone can die, a condition called osteonecrosis, which may lead to failure of the implant to fully integrate or bond with the jawbone). Typically in most implant systems, the osteotomy or drilled hole is about 1mm deeper than the implant being placed, due to the shape of the drill tip. Surgeons must take the added length into consideration when drilling in the vicinity of vital structures.
Once properly torqued into the bone, a cover screw is placed on the implant, then the gingiva or gum is sutured over the site and allowed to heal for several months for osseointegration to occur between the titanium surface of the implant and jawbone.
After several months the implant is uncovered in another surgical procedure, usually under local anesthetic by the restorative dentist or prosthodontist, and a healing abutment and temporary crown is placed onto the implant. This encourages the gum to grow in the right scalloped shape to approximate a natural tooth's gums and allows assessment of the final aesthetics of the restored tooth. Once this has occurred a permanent crown will be fabricated and placed on the implant.
An increasingly common strategy to preserve bone and reduce treatment times includes the placement of a dental implant into a recent extraction site. In addition, immediate loading is becoming more common as success rates for this procedure are now acceptable. This can cut months off the treatment time and in some cases a prosthetic tooth can be attached to the implants at the same time as the surgery to place the dental implants.
In all of these approaches, computer-based guidance has thrust itself onto the treatment stage. Not only will 3D digital imagery yield critical treatment guidance, the digital data can be used to manufacture precision drilling guides, virtually eliminating surgical errors.